Blog
Reamers: Sizes, Shanks and Cutting Speed for Trade Use
Buying Reamers is less about picking a brand than about matching three or four figures to the job in front of you. Get those right and the tool disappears into the work; get them wrong and the same money buys something that fights you every time.
The range runs to 17 options priced between $8.99 and $26.97. Prices move with the specification, so it is worth reading the option list before deciding which end of the range suits the work.
What decides how a reamer performs
Four things decide how a reamer performs: size, material, build and the price band it sits in. The table below shows what each one changes in practice.
| Factor | What it changes | Typical choices |
|---|---|---|
| Point angle | 118 degrees suits general steel, 135 degrees splits a harder surface. | 118 / 135 / 90 degrees |
| Coating | HSS, cobalt and titanium coatings trade heat resistance against price. | HSS / cobalt / TiN |
| Flute length | Deep flutes clear swarf and reach past a boss. | Standard / long / extra long |
| Shank type | Straight, reduced and SDS shanks fit different chucks. | Straight / reduced / SDS-Plus |
| Material | Carbide cuts masonry and stone, HSS cuts metal, brad point cuts timber. | HSS / carbide / brad point |
Worth knowing: the cheapest option in a range is rarely the one that costs least over time, because consumables and replacement parts follow the purchase.
Bit selection by material
There is no single best type, only the type that matches the work. This is where the choice is usually won or lost.
| Material | Bit | Speed |
|---|---|---|
| Mild steel | HSS 118 or 135 degree | Slow, with cutting oil |
| Stainless | Cobalt, 135 degree | Slower still, steady feed |
| Brick and block | Carbide masonry | Hammer mode |
| Concrete | SDS carbide | Rotary hammer only |
Drilling a hole that comes out on size
Good results come from a repeatable method rather than from force or guesswork. Work through the table in order and the outcome is predictable.
| Step | What to do | Why |
|---|---|---|
| Centre punch | Mark the spot accurately | The bit follows the dimple |
| Start square | Sight the bit from two directions | A tilted start makes an oval hole |
| Use cutting fluid | A drop on steel, none on cast iron | Heat is what dulls the edge |
| Clear the flutes | Peck the drill every few seconds | Packed swarf welds to the cutting edge |
Reamers in this range
The listing below is the option this guide is built around. It shows the current price and the full specification.
Every option in this range
Every option in this range is listed below with its price, so the whole ladder can be read at once.
| Part of the range | Price | Options | Notes |
|---|---|---|---|
| Lower third of the range | $8.99 to $25.85 | 5 options | The sizes most buyers start with |
| Middle third of the range | $26.97 to $26.97 | 6 options | Where most of the value sits |
| Upper third of the range | $26.97 to $26.97 | 6 options | For heavy or continuous work |
Reading the ladder, the real jump in capability comes once rather than at every step, so it pays to find that step and buy there.
Prices and what the money buys
Two costs matter more than the purchase price: what has to be replaced, and how often. An option that costs a little more and lasts twice as long is the cheaper one over a year of work.
Looking after reamers
Nothing in this range needs much looking after, but the small routines below are what separate an item that lasts a decade from one that lasts a season.
- Wipe bits dry and oil them before they go back in the index.
- Resharpen at the same point angle, or replace the bit.
- Never hammer a bit that is not made for impact.
- Check an SDS shank for burrs; a burr ruins the chuck.
- Keep taps cutting with the correct lubricant and a quarter turn back.
- Store taps in their box so the flutes do not chip.
Buying in quantity
Ordering more than one changes the calculation. Unit prices for larger quantities are quoted separately, and the saving usually appears once the order goes past a small multiple rather than on the second item.
For trade buyers the practical question is how many will be consumed in a year. Buying a year’s worth at once removes the cost of repeat shipping and the risk of a size going out of stock mid job.
Fitting and first use
Check the item against the listing as soon as the parcel is opened. Size, option and finish are the three things that are wrong when something is wrong, and all three are obvious in the first minute.
Read the maker’s clearance and torque figures before the first use rather than after. Nearly every early failure in a range like this is an installation problem rather than a manufacturing one.
Common mistakes
The commonest mistake is buying for the worst job rather than the usual one. A specification chosen for a task that happens twice a year is carried through every day of the other three hundred and sixty.
The second commonest is ignoring the consumables. What has to be replaced, and how often, decides the real running cost far more than the purchase price does.
What arrives with the order
Each option is supplied as a complete unit, packed for transport and despatched by the carrier selected at checkout. Options in this range are priced individually, so the packing list follows the option chosen rather than a fixed bundle.
Where an option includes a case, a set or a spare, the listing says so against that option. Anything not listed against the option is not part of it, which keeps the price comparison honest.
Frequently Asked Questions
These are the questions that come up most often about Reamers.
Why does my drill bit burn instead of cut?
Speed too high, feed too light, or a blunt edge. The bit is rubbing rather than cutting, and rubbing is what makes heat.
How do I stop a tap snapping?
Keep it square, back it off a quarter turn every half turn forward, and use the right lubricant for the material.
What size pilot hole do I need for a tap?
The nominal diameter minus the pitch. A chart for the thread standard gives the exact figure in seconds.
Do prices include delivery?
Prices are shown per unit and exclude shipping. Delivery is calculated by weight and destination at checkout, and the shipping policy sets out the rates in full.
Can I order in larger quantities?
Yes. Trade and bulk orders are welcome, and pricing for larger quantities is quoted on request rather than taken from the single unit price.
Choosing the right one
Choosing well comes down to matching the specification to the work rather than to a budget. Work out the size, then the material, then the build, and the price follows.
The Reamers range here covers every option listed above, with live stock and pricing.
If two options look equally suitable, take the larger one only if the work is likely to grow. Otherwise take the smaller and keep the difference for consumables.
