Soldering Iron, 60 W, Adjustable Temperature, 220 V, Mica Element

Sixty watts is the size that will solder a wire joint and still heat a small connector or a piece of sheet without waiting. This one has a dial on the handle for temperature, and a mica element, which is the element pattern that survives being left switched on. Made by Huanghua.

60 W Soldering Iron: Overview

The rating decides what the iron can do. Sixty watts heats a joint quickly, which matters because a slow iron means holding the bit on the work until the surrounding materials are damaged. It also has enough reserve to solder a heavier wire or a connector tab.

Temperature is set on a dial rather than fixed by the element. That lets the same iron run hot for a chassis joint and cooler for a small printed circuit board pad, which is the difference between a clean joint and a lifted track.

The heating element is mica, and the handle is a rubber grip with the dial at the front, so the temperature can be changed without putting the iron down.

Key Features at a Glance

• 60 W – heats a joint quickly, with reserve for heavier work.
• Adjustable temperature – dial on the handle.
• Mica element – a robust element pattern for regular use.
• 220 V mains – no separate station needed.
• Rubber grip handle – the dial is within reach of the thumb.
• Two models – 905C and 905CS.

Soldering with a Mains Iron

Making a joint

Heat the joint, not the solder. Hold the bit against the wire or pad until the solder flows onto it, then take the bit away and let the joint set without moving it.

Clean the bit on a damp sponge before each joint and keep it tinned. A dry, oxidised bit transfers heat poorly, which is what makes an iron feel too small for the job.

Setting the temperature

Run hot for chassis and connector work, and cooler for small pads and thin insulation. Turning the iron down rather than working faster is what protects the board.

Let the iron reach temperature before the first joint. Working with a bit that is still warming is how a track gets lifted.

Care and Safety

Bits and element

Replace the bit when it stops taking solder or the tip has eroded. A pitted bit cannot be dressed back to shape.

Rest the iron on its stand, never on the bench. A mains iron left on the bench will burn the surface and the cable.

Safety

Keep the cable away from the hot barrel and unplug the iron when it is not in use. Most soldering iron damage is a scorched cable, not a burnt joint.

Work in a ventilated area, since flux fumes are the part of soldering that is worst for the operator.

Available Models and Prices

Two models are in stock. Prices are per iron in USD.

Specifications

Packaging Information

Irons ship individually boxed. Carton quantities are available on request.

Where It Is Used

Soldering wire joints and connectors, electronic repair and hobby work, tinning and small sheet metal work, and general electrical work where a mains iron is quicker than a station.

Choosing the Right Item

1. Match the thread and the capacity to the equipment: the 3/8 cylinders suit common inflator heads and smaller life jackets, and the M16 x 1.5 cylinder suits the larger jacket and raft systems.
2. Buy the capacity for the job. An 8 g cylinder will inflate a bracelet or top up a tyre, while a car tyre or a tubeless bicycle tyre needs 38 g or more.
3. For a workshop, buy a power rating above the job: a 60 W iron heats a joint quickly and has reserve for a connector, which a 30 W iron does not.
4. Order cartons rather than singles where the consumable is used regularly, and check the shipping declaration for pressurised goods at the same time.

Care and Maintenance

Keep cylinders and consumables dry and out of direct sun, and check the rules that apply to pressurised goods before shipping in bulk.

Check threads against the head, mechanism or fitting before ordering: a 3/8 cylinder will not fit an M16 mechanism, and the two look similar in a photograph.

Unplug tools when they are not in use, keep cables away from hot parts, and work in a ventilated area where flux or gas is involved.

OEM and Bulk Supply

The supplier makes to order, prints own-brand packaging and can supply private-label cartons, with OEM and ODM support for welding and inflation accessories.

Frequently Asked Questions

Which options are available?

This listing covers 2 options: Model 905C, 60 W; Model 905CS, 60 W. All are in stock and priced individually.

What is it used for?

Soldering wire joints and connectors, electronic repair and hobby work, tinning and small sheet metal work, and general electrical work where a mains iron is quicker than a station.

Can I buy in bulk or with my own branding?

Yes. Own-brand printing and private-label cartons are available on request, with OEM and ODM support.

Summary

Sixty watts is the size that will solder a wire joint and still heat a small connector or a piece of sheet without waiting. Offered in 2 configurations, each priced separately.

Typical use: Soldering wire joints and connectors, electronic repair and hobby work, tinning and small sheet metal work, and general electrical work where a mains iron is quicker than a station.